In Stock
48V 10Amp AC to DC LFP (LiFePO4) Battery Charger
The DCS-LFP-1025 is a fully automatic AC mains to DC 48V LiFePO4 charger. This is a IP-65 spec charger, suitable for boats, caravans or ideal as an off grid backup charger. It has been specifically developed to be used as an onboard charger for golf carts.
10Amps at 51.2V (600W continuous)
Availability: Out Of Stock, Next Batch Early April
In Stock
The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
The SmartShunt is available in 500A & 1000A.
This NMEA2000 drop cable makes the BMV-700 information available to an NMEA2000 networks. Battery information such as voltage, current and state of charge can be displayed on common purpose displays from other manufacturers which accept the NMEA2000 data being sent.
NMEA 2000 requires a single backbone where products must connect to with drop cables. The BMV drop cable is equipped with a Micro-C (M12) male connector for this purpose, intended to be connected to a corresponding T-connector in the backbone.
It transmits monitoring information, AC voltages and currents, DC voltages and currents and the state. Other NMEA2000 devices can also send commands to the VE.Bus product to turn it on or off, or change the input current limit.
NMEA 2000 requires a single backbone where products must connect to with drop cables. The VE.Net to NMEA 2000 drop cable is equipped with a Micro-C (M12) male connector for this purpose, intended to be connected to a corresponding T-connector in the backbone
Explosion-proof / No leakage
Low Internal Resistance / Proven Stability
Ultra-long cycle life
Contracted A Grade cell supply
DCS Batteries are the ideal replacement & upgrade from AGM, Gel or other lead-acid batteries for any application. DCS gives you the ability to upgrade your current batteries to lithium-ion technology that can deliver a minimum of 2500 cycles and has tremendous advantages in weight, performance, reliability and service life compared to traditional lead-acid batteries.
Backed by a 3 year warranty.
This interface is used in Hub-1 systems with grid-feedback enabled. It interfaces between the VE.Bus system and one or more MPPT solar chargers with a VE.Can connection: the MPPT 150/70 and/or MPPT 150/85. Many of our customers integrate our products into their own systems, using data communication protocols. There are several options to establish data communication.
DCS 200AH Lithium Slimline Battery Tray Includes: 2mm lazer cut stainless steel construction. Screw in or bolt in fixture using 8 x pre-drilled fixing points.
Overall external footprint of the trays is 520 x 160 x 350mm
Australian designed and made here in Brisbane.
In Stock
In Stock
Calculates;
The Skylla Control allows you to alter the charge current of Skylla Charger. It is simple and easy to operate. It also helps you see the system status through LED indicators.
Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.
In Stock
These laser cut stainless steel brackets are designed for use only with the DCS 12V 130Ah hybrid batteries when installed inside the Toyota Land Cruiser 200 series.
Availability: In Stock
This panel is intended for switching on & off all the models of Skylla-TG Charger. It is simple, easy to operate, and user-friendly. It shows the status of inverter through the LED indicator.
This low power Zigbee standard allows for wireless data transmission over short distances. This devices are standard DC5-12V power and come with a small external antenna.
ARGO DIODE Battery Isolator with voltage compensating diode and alternator energize input.
This low power Zigbee standard allows for wireless data transmission over short distances. The devices are USB 5V power and come with a small external antenna
This NMEA2000 cable is used to connect a Victron product with a VE.Can port to a NMEA2000 network. NMEA 2000 requires a single backbone where products must connect to with drop cables. The BMV drop cable is equipped with a Micro-C (M12) male connector for this purpose, intended to be connected to a corresponding T-connector in the backbone.
The VE.Bus Smart dongle is a Bluetooth Smart enabled VE.Bus interface, with battery temperature-and-voltage sensing. It communicates system information straight to your smart phone – using the free-to-use VictronConnect app.
When used with Multi- inverter/chargers the dongle provides on-battery temperature and voltage sensing capabilities – allowing compensation for possible cable losses which can occur during charging and discharging.
Phoenix chargers are ready to communicate with a computer through its RS-485 data port. All you need to link to your PC in order to be able to set and read out all parameters.
The MK3-USB allows you to connect your computer with all inverters and inverter/chargers that have a VE.Bus communication port.
The VE.Direct to Global remote interface allows you to connect BMV 700 series products to a Global Remote. It is used to make BMV-700 information available on the Global remote.
Phoenix converters can communicate with a computer through their RS 232 communications port. All you need to connect your PC, in order to set up and read all the parameters, is the data connection kit as shown.
The Argo Battery Combiners feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V.
The SmartSolar plugged Display is a controller LCD display for the SmartSolar Charge Controllers. Simply remove the rubber seal that protects the plug on the front of the controller and plug-in the display.
With the VE.Direct to Bluetooth Smart dongle you can get live status info, see historical values as well as configure Victron products. The dongle works together with the VictronConnect App, available for both Android and iOS devices. The dongle can be connected to almost all Victron products that have a built-in VE.Direct port.
The AC Current sensor is a simple external current sensor used to measure AC Current, Power (VA) and calculate energy of a PV Inverter connected to the AC input or output of a Multi or Quattro. Use the AC Current sensor to measure and visualise the solar production of a PV Inverter. The measurements will be visible on the GX device and on the VRM Portal.
Cables with M8 circular connector is used for 12.8V Li-Ion batteries. It is available in different sizes i.e. Male to Female 3 pole 1 m (bag of 2), Male to Female 3 pole 2 m (bag of 2), Male to Female 3 pole 3 m (bag of 2), Male to Female 3 pole 5 m (bag of 2). You can order any of them according to your choice.
In Stock
Victron Energy RJ12 UTP Cable is available with different sizes including 0.3 m, 0.9 m, 1.8, 3 m, 5 m, 10 m, 15 m, and 30 m. For use with ESP System, BMV-600 and BMV-700 Energy meters, this is a replacement for the cable that joins the shunt and the meter.
(Electronic fuse version) (Micro blade compatible)
The Toyota MK3 microblade version of the Alternator Voltage booster from all other diode booster units in that it is the only device of its type available that incorporates an auto resetting PTC fuse.
In Stock
With this cable the charge control feature of the BMS 12/200 can be used together with the VE.Bus BMS. The BMS 12/200 will limit charge current by the alternator to a safe value, and and stop the charge process in case of an alarm (the Li-ion battery is communicates with the VE.Bus BMS and the VE.Bus BMS transmits to the BMS 12/200)
A cable to connect VE.Can, VE.Bus, VE.Net, and VE9bitRS485 devices. Victron Energy RJ45 UTP Cable is available in different sizes including 0.3 m, 0.9 m, 1.8, 3 m, 5 m, 10 m, 15 m, 20 m, and 30 m.
If you have installed an MPPT Solar Charger, especially, if it is installed in an area that is easily accessible, it is necessary for you to install the MPPT WireBox as it provides an extra level of safety. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.
If you have installed an MPPT Solar Charger, especially, if it is installed in an area that is easily accessible, it is necessary for you to install the MPPT WireBox as it provides an extra level of safety. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.
This cable is intended for on/off control of the Skylla-i when the source signal is high when the Skylla-i must be on, and low or free floating when Skylla-i must be off. Use this cable to connect a Skylla-i to a VE.Bus BMS. The VE.Bus BMS will then disable the Skylla-i charger when the batteries are fully charged.
This temperature sensor is suitable for the BMV-702, 712 & Smart Shunts
The Victron Energy RS485 to USB Interface allows you to connect the energy meter ET112 or ET340 to the Color Control GX. It is used for direct connection. There are two options available regarding the length of cable and you can choose any of them according to your requirements. It is available in 1.8m cable length and 5.0m cable length.
Victron Energy temperature sensor for Venux GX, Phoenix MultiPlus and Quattro. It helps you in monitoring the temperature of your Victron Energy products. Quattro and Multiplus units are supplied with this temperature sensor. For Venux GX or if any the temperature sensor of your Phoenix MultiPlus and Quattro is damaged, you can order it now.